UL 10C vs. UL 10B: What Each Fire Door Test Means

Author: Esteban Galicia

Updated:

Decorative fire door test title card

UL 10B and UL 10C are both fire tests for door assemblies, and the difference is furnace pressure. UL 10B holds the furnace close to atmospheric pressure. UL 10C runs the test under positive pressure, which pushes hot gases through the gaps around the door and is closer to what happens in a real fire. For most swinging doors in new work, the label you want to see is UL 10C.

This guide explains what each test does, where codes point you, and what to check before you order doors, frames and hardware.

Ufdoors
Specify Fire-Rated Doors With Confidence
Ufdoors manufactures and installs fire-rated steel doors, frames, and hardware focused on NYC fire and safety standards.
Visit Ufdoors

TL;DR

  • UL 10B is the neutral-pressure test. UL 10C is the positive-pressure test, and it is the one most swinging fire doors are now expected to meet.
  • New York City code points side-hinged and pivoted swinging doors to NFPA 252 or UL 10C. Other assembly types, such as horizontal sliding doors, can still fall under UL 10B.
  • A fire door is an assembly. The door, frame, hardware, glazing and labels must match what was tested.
  • A test standard on a data sheet does not make a door code-approved for your opening. Check the label, the required rating and the local code.

Table of Contents

What UL 10B and UL 10C actually test

Both standards evaluate a complete door assembly in a furnace. UL Solutions describes UL 10B as the standard for fire tests of door assemblies and UL 10C as its positive-pressure version. Both are opening-protective tests. They look at whether flame passes through, whether the door stays in the opening, whether the hardware keeps the door closed, and whether the door stays within deflection limits for its type.

UL 10C covers swinging door assemblies, including frames with lights and panels, and measures their ability to remain in a wall opening during a specified fire exposure. The scope excludes a swinging door that is part of a larger assembly, such as a sliding fire-door assembly, and doors intended as elevator entrances.

That last point matters. UL 10C is not a universal upgrade that replaces UL 10B for every opening. It applies to swinging doors.

How the pressure conditions differ

In a real fire, hot gases expand and build pressure. The upper part of a room is usually under positive pressure, and the lower part is drawn toward negative.

The older UL 10B test did not model that. Its furnace pressure was kept as nearly atmospheric as possible, with the neutral pressure plane near the top of the door assembly. UL 10C moves that plane down. The neutral pressure plane is set 40 inches above the bottom of the specimen, so the area above it is under positive furnace pressure.

UL 10B and UL 10C pressure planes compared

The New York City code states it as a requirement. For side-hinged or pivoted swinging doors tested under NFPA 252 or UL 10C, the furnace neutral-pressure level must be at 40 inches (1,016 mm) or less above the sill after five minutes.

Why it changes the result

Positive pressure forces hot gases out through the gaps between the door and frame. That raises the chance of the edges and gaps degrading. Where pressure is negative, ambient air is drawn into the furnace through the same gaps, and the test is gentler. The practical consequence is that positive-pressure testing produces conditions closer to a structure fire.

In plain terms, UL 10B is a fair test of a door that sits in a mostly still fire. UL 10C is a harder test of the gaps, seals and edges, which is where real fires push smoke and flame through.

UL 10B vs. UL 10C at a glance

Feature UL 10B UL 10C
Name Fire Tests of Door Assemblies Positive Pressure Fire Tests of Door Assemblies
Furnace pressure Neutral, kept close to atmospheric Positive above the neutral plane, set 40 inches above the sill
Scope Door assemblies of various types Swinging door assemblies
Gap stress Lower Higher, hot gases pushed through gaps
Typical use in current NYC code Horizontal sliding doors, swinging elevator doors, fire shutters Side-hinged and pivoted swinging doors, corridor and smoke-barrier doors

The last row comes from the New York City code section on door assemblies. Other assembly types fall under NFPA 252 or UL 10B, and corridor and smoke-barrier door assemblies are generally directed to UL 10C or NFPA 252, subject to stated exceptions.

What the hose stream test adds

After the fire exposure, the assembly is hit with a hose stream. It adds cooling and erosion to the exposed side and checks whether the door holds together after heating. The hose stream is part of the test method under both UL 10C and NFPA 252.

There is an exception to know. Fire-door assemblies in corridor and smoke-barrier walls are not required to pass the hose stream test of UL 10C or NFPA 252. That applies to those wall types only, and your local code edition governs it. Do not assume a door without a hose stream result suits a rated stairwell or shaft wall.

Which standard do codes require?

The answer depends on door type, code edition and city.

  • Model codes. The International Building Code allows swinging fire doors to be tested to UL 10C or NFPA 252. The 2018 and 2021 editions require positive-pressure testing, while model codes still allow UL 10B for some door types. The Steel Door Institute says the IBC requires most fire-door assemblies to be tested to UL 10C or NFPA 252 with the positive-pressure method.
  • New York City. Side-hinged and pivoted swinging doors use NFPA 252 or UL 10C. Horizontal sliding doors, swinging elevator doors and fire shutters use NFPA 252 or UL 10B. The city table sets minimum ratings by wall rating and assembly type.
  • Other jurisdictions. Local amendments and older adopted editions differ. The Window and Door Manufacturers Association advises that architects, contractors and distributors know local requirements so the right neutral- or positive-pressure door is supplied.

If you are replacing a door in an older building, the existing UL 10B label may have been correct when it was installed. If you are specifying a new swinging door today, ask for UL 10C.

Can a UL 10B door stay in place?

Often yes, when the opening was legally rated and the door is in good condition. The question changes when you alter the opening, change the wall rating, or the inspector or authority asks for current labels. Have the opening reviewed before you assume. Our fire door inspection service checks labels, gaps, closers and latching against what the opening requires.

Ratings and durations

UL 10C assemblies can receive ratings of 20, 30, 45, 60, 90, 180 or 240 minutes, based on the duration of fire endurance tested. The rating on the label tells you how long the assembly was tested, not how long it will last in every fire.

The minimum rating you need comes from the wall type and use of the opening. It does not come from the test standard. A 90-minute door needs to match a rated wall of the right class, and the code table tells you which. Our guide to fire-rated door ratings and requirements walks through choosing a rating.

A listing does not mean the door is code-approved

This is the most common misunderstanding behind the keyword. A UL 10B or UL 10C test shows how an assembly performed during the test exposure. UL 10C tests are intended to register performance during the exposure and do not determine suitability for use after a fire.

Two more distinctions help:

  • Fire protection vs. fire resistance. Fire-protection-rated door assemblies are different from fire-resistance-rated assemblies, which may be tested to UL 263 or ASTM E119. A door is not a wall.
  • Test lab vs. approval. The standard is the method. The authority having jurisdiction decides whether the product and installation meet code for that opening.

Reading the label

A fire-door label must carry the manufacturer’s name or traceable identification, the name or trademark of the third-party inspection agency, and the fire-protection rating. If any of the three is missing, painted over or cut off, an inspector can reject the opening. Labels also have nothing to do with surface burning ratings such as those in this flame spread index guide. Those describe finishes, not door assemblies.

What has to match the tested assembly

A fire door is a complete opening. The assembly includes the door, frame, hardware, glazing and other accessories, so every component has to be part of the tested system.

Check these before you order:

  1. Door and frame. The door’s rating and construction must be allowed with the frame you pair it with. Our hollow metal frames and fire-rated steel doors are sold for this kind of matched opening.
  2. Hardware. Hardware evaluated for fire doors must hold the door closed, and the latch bolt must remain projected and intact after the test. Browse commercial door hardware with that in mind, and avoid hold-open devices or locks not listed for the door.
  3. Glazing. Putting fire-resistance-rated glazing into a fire-protection-rated frame can cause failure. The Steel Door Institute cautions that these components must be tested together as one integrated assembly.
  4. Seals and gasketing. Under positive pressure, the edge seals matter more. Do not remove, paint over or swap them casually.
  5. Installation. A listed door installed with wrong clearances or missing anchors is no longer the tested assembly. See our door and frame installation service.

Our perspective

Most of the calls we get come down to one question: what do I put in this opening, and will it pass? In practice, the test standard is rarely the hard part. The hard part is that the label, the frame, the hardware and the wall rating all have to agree.

Our perspective — overview diagram

We see three patterns. A contractor buys a door from a spec sheet, and the frame is a different rating. A property manager replaces a closer or lockset with a part that is not listed for the door. Or an old UL 10B door sits in an opening that is being altered, and nobody checks the current requirement. Each one is cheap to fix before the order and expensive after a failed inspection.

Our advice is simple. For a new swinging door, specify UL 10C unless the code section for your opening says otherwise. Check the label on the door and the frame. Order hardware listed for that door. And when you cannot tell what is in the wall today, have the opening looked at before you spend money. New York City work adds its own details, and we handle them every day for contractors, property managers and architects.

— Esteban

Getting compliant doors without the delay

When a door fails inspection or is damaged, the building is waiting on you. We manufacture and supply fire-rated steel doors, hollow metal frames and commercial door hardware, and offer supply, installation and service together, with same-day or next-day delivery. You can see the fire-rated steel door range, or order a complete steel door unit with frame and hardware. If a door needs repair or replacement urgently, use our emergency door service. Pricing is not published on the site, so contact us for a quote.

A short checklist for your next order

  1. Find the wall rating and the opening type in your plans or the code table.
  2. Confirm whether the code section for that opening calls for UL 10C, NFPA 252 or UL 10B.
  3. Pick a rating that meets or exceeds the required minimum.
  4. Match the door, frame, glazing and hardware to one listed assembly.
  5. Confirm the labels are legible and carry the manufacturer, the inspection agency and the rating.
  6. Keep the paperwork, and schedule routine checks. Our commercial door maintenance program covers upkeep.

FAQ

Is UL 10C better than UL 10B?

For swinging doors, UL 10C is the more demanding and more realistic test, because it applies positive pressure that pushes hot gases through gaps. That is why current codes lean toward it. It is not better for every door type, since UL 10C does not cover sliding assemblies or elevator entrances.

It depends on the door type, the code edition and the jurisdiction. Model codes still allow UL 10B for some door types, and New York City directs several non-swinging assemblies to it. For a swinging door in new work, expect UL 10C or NFPA 252 to be required.

Does a UL 10C label mean the door is code-approved?

No. The label shows the assembly was tested and listed at a given rating. Whether it is approved for your opening depends on the required rating, the matching frame and hardware, correct installation and the local authority.

Do UL 10C doors need a hose stream test?

The test method includes it, but fire-door assemblies in corridor and smoke-barrier walls are not required to pass it. Other openings generally are, so confirm with your code edition.

Sources

Older Posts Newer Post